Local 401.216.7900
 |
 |
| Request Quote |
The new PowerPinner 7105HS boasts the quickest cycle time and most reliable welds available. Thanks to a technological breakthrough, the 7105HS high speed welder is built with the same high quality materials you have come to expect form Gripnail. Functioning without any mechanical reeds switches, the 7105HS on-board computer has been turbo-charged for peak performance. The new Programmable Logic Controller produces welding speeds never before seen without sacrificing welding quality.
Contractors who regularly line large fittings and straight duct will find the convenience of the 7105HS speeds their assembly and reduces fabrication costs. The weld head travels a full 60 inches for lining 5-foot wide duct. The head is moved with a multi-position extension arm and glides on specially designed bearings, while all wires are reinforced in a wire sleeve and securely housed in an energy chain.
At 83 cycles per minute, the new PLC reaches coil line speeds.*
Depressing the ergonomic foot pedal while the Continuous Fire switch is on allows the operator to continuously weld pins without having to lift their foot off the pedal.
Upwards of 25 pins are available from the lower track before additional pins are speed loaded from the upper track.
Produces the strongest possible welds for 1/2" all the way to full" pins fastened to 16-26 gauge sheet metal.
* Numbers based on Weld Setting 1
For peak performance, it is highly recommended using Gripnail's wide range of PowerPoint Weld Pins. Each point is precisely formed to provide optimum electrical resistance.
A PowerPoint Weld Pin permanently attaches insulation to galvanized steel in fabrication of HVAC ductwork and withstands a tensile pull of at least 120 pounds in sheet metal.
Inside the control box is a PLC, which has been programmed here in the USA, to coordinate welding and machine functions resulting in the fastest and most perfected weld every time. Machine operators only need to increase the weld setting for longer pins or thicker sheet metal, and the PLC will set the dwell time and coordinated the feed cycle. Minimal operator training is needed for this machine which means maximum flexibility. The PLC even has a diagnostic screen should a machine element require attention.
The PLC allows for minimum operator intervention during setup or job changes, all while producing maximum performance at industry leading speeds.
The magnetic upper weld tip is specially designed with a chamfered edge and recessed center to optimize the weld quality of PowerPoint Weld Pins. The unique characteristics of the PowerPoint weld pin's noninvasive protruding shank captures and centers the weld pin to ensure consistent loading, while the beveled retaining cap prevents it from shifting off the weld tip when the pin is being set through the insulation. Although the PowerPinner 7105HS works with a variety of weld pins, using our PowerPoint's precision manufacturing process assures a trouble-free operation with the best quality weld possible.
Upper and lower weld tips can be replaced in seconds. The lower weld tip is purposefully off centered so that once an area is worn down, the operator can make a small rotational adjustment and use a new part of the weld tip for extended product life.
To keep up with the intense speeds of the PLC, double-acting load cylinders are standard on every machine. This ensures that each Weld Pin is loaded at maximum speeds without the danger of a component collision potentially possible with single-acting cylinders, which may lag due to its dependence on spring tension.
A single weld-setting switch controls the weld time while the PLC optimizes the dwell time. The other controls are a "continuous fire" on/off switch and a feeder bowl speed control. The PowerPinner 7105HS also comes with a LED voltage readout which informs the operator of a low voltage situation which can affect the integrity of the weld.
Safety - A high visibility power switch comes standard with a simple to use Lockout/Tagout features.
To protect vital components from the rigor of most manufacturing environments, every electrical enclosure is rated to the National Electrical Manufacturers Association's Type 12 standards. This protects your investment from dust, debris, adhesive remnants and oil vapor from reaching operation critical components.
The large capacity feeder bowl can accommodate a full range of pins from half inch to 2 inch and operators can control the pin feed speed on the control box.
